Instructions for Digil fingerprint lock, Keylock,Dig fingerprint password lock operation manual, Laiwu fingerprint lock battery replacement.
How to modify the password of Digil fingerprint lock? How to reset the fingerprint lock of Digil password? Digil owns two classic brands, Digi and Keylock, among which Keylock is well used in China and has been supported by many users. Many friends may not be able to operate the fingerprint lock of Digil Keylock password. The general operation can be carried out according to the instructions. If the instructions are missing or lost, you can see the relevant introduction in this article.
Description of the operation steps for entering and modifying the fingerprint lock of Digil password: Laiwu, Jinan, specializes in installing fingerprint locks, Laiwu fingerprint lock specialty store and Laiwu smart lock specialty store 0531-78588110.
1. Open the back cover: to initialize or set the management fingerprint, you must open the back cover before you can operate.
2. Set management fingerprint: this function can be set into management fingerprint, which has the highest authority and can add and delete fingerprints of ordinary users. Each lock can have two management fingerprints.
A. Press the initialization button on the circuit board, and you will hear a "beep" and the traffic lights will flash at the same time.
B. At this time, click the finger to manage fingerprints (which is required to be never entered) on the fingerprint collector. If this fingerprint is successfully collected, it will ring and the indicator light will blink alternately from the traffic light to the green light.
C. Continue to press the same fingerprint for three times, and each time it is pressed, a short "beep" will be issued.
D. If the entry is successful, a long beep will be issued. If it fails, it will sound "beep-beep" twice.
E, when the operation is finished, exiting the state of entering and managing fingerprints.
Note: If the fingerprint to be entered has been entered before the operation, the operation will not be successful, and three sounds of "beep-beep-beep" will be issued.
If you want to enter the next management fingerprint, please repeat the above steps.
Important note: * The factory bus code is "11111111", please modify the bus code when using it for the first time. * The password is 8 bits long.
1. This lock can store up to 78 passwords and 150 fingerprints;
2. If the reset operation is successful, the lock can be set to the factory status, that is, the mother code is set to "11111111" and all sub codes are cleared, and all user fingerprints are also cleared.
3. The user number range is arbitrary 3 digits; The user password is any 8 digits.
First, unlocking operation Jinan Laiwu professional installation fingerprint lock, Laiwu fingerprint lock store, Laiwu smart lock store 0531-78588110
1. Password to open the door: directly enter the 8-digit correct password to open the door normally;
2. Fingerprint opening: When the blue background light of the fingerprint collection window is on, place your finger correctly and open the door normally after confirmation.
Second, increase password users
Press "1+*"+mother code +3-digit user number+user password+user password+"#". Example: If you need to add user 111, and the initial password is 12312301, please operate as follows:
Press "1+*"+mother code+"111"+"12312301"+"12312301"+"#"
Third, delete the password user
1. Delete by user number: press "2+*"+mother code +3-digit user number +3-digit user number+"#"
2. Delete all sub-passwords: press "3+*"+mother code+"#"
Fourth, modify the password (subcode, mother code)
Press "0+*"+modified password+new password+new password+"#"
V. Opening channel function
Press "*+*"+mother code+"#"
Sixth, cancel the channel function
Press "*+*"+mother code+"#"
Seven, increase user fingerprints
1. Add fingerprint users with user numbers.
Press "1+#"+mother code+"3-digit user number"+"#"+fingerprint+"di-"and make a long sound (you can enter the next user number).
2. Add fingerprints at will
Press "1+#"+mother code+"#"+fingerprint+"di-"for a long sound (the next fingerprint can be entered).
Eight, delete the user fingerprint
1. Delete a single fingerprint user with the user number.
Press "2+#"+mother code+"3-digit user number"+"3-digit user number"+# "
2. Delete fingerprints directly with your fingers.
Press "2+#"+bus code+"#"
Nine, delete all fingerprint users
Press "3+#"+bus code+"#"
Note: 1. Open the front cover of the lock; When the blue background light of the fingerprint collection window is not on, repeat the operation until the light is on;
2. When adding a user, in order to delete the user in the future, please be sure to write down the user number to facilitate management.
3. Description of prompt tone: "Di-"means pressing the number key tone; "Di-di-di-"three sounds are operation failure; After opening the door, the four tones of "di-di-di-di-di-"are low voltage prompts; Other operations succeeded in a long tone of "di-".
4. Reset: first open the front cover, then open the back cover with a special tool, remove the power cord, short-circuit the positive and negative poles of the power cord with metal (or wait for a while), press and hold the keys "1, 2" continuously, then connect the power cord, and wait for a long tone of "di-",that is, the operation is successful.
5. When in the channel state, open the front cover of the lock and open the door when the blue background light of the fingerprint collection window is on.
6、6600-98、6600-92； External emergency DC 9V power supply is available.
Matters needing attention in the use of Digil password fingerprint lock
1. When inputting or comparing fingerprints, the operation may be unsuccessful or the quality of the collected fingerprint image may be degraded due to the deviation of the position where the fingerprints are placed in the fingerprint collector. Please try to put your finger in the center of the fingerprint collector when entering fingerprints.
2. Digil fingerprint lock should not be used outdoors or in strong sunlight. If you can’t work normally because of the strong sunlight, you can block the sunlight with an object before pressing your finger.
3. Digil fingerprint lock adopts optical fingerprint collection. Please be careful to protect the collector or avoid getting dirty when using it.
4. When entering fingerprints, the finger should not be pressed on the fingerprint collector for too long, and about 0.5 seconds is appropriate. If it is left for too long, it will affect the acquisition effect.
5. The Digil fingerprint lock will be dormant when it is not working. When you press your finger, the light of the fingerprint collector will light up, so don’t move your finger. Don’t move your finger until you hear a signal sound. If you remove your finger before the signal sounds, it will be considered as an illegal fingerprint.
6. When using, ensure that the working voltage of the Digil fingerprint lock is 3.6VDC —- 5VDC, and do not connect the positive and negative poles of the input power supply reversely. It is recommended to charge the Digil fingerprint lock before installation.
Battery voltage: 3.6V-4.1VDC; Static current: 20uA — 30uA；; Working current: 250mA；; Fingerprint capacity: 1000 pieces; Identification time: < 2 seconds;
Rejection rate: 1.4%, recognition rate: 0.00001%; Service temperature:-20 C-55 C Storage environment temperature:-40 C-80 C.