The curtain has fallen on double 11, and the last payer can successfully land and become a happy recipient these days. Perhaps you are experiencing the joy of unpacking the courier, or are you still worried about how to install the smart lock that has just arrived?
In the smart lock ring, it is often said that "the 10-point stability of smart locks is composed of 7-point quality and 3-point installation". According to statistics, more than 50% of after-sales problems in the market are almost caused by improper installation.
So, what should we pay attention to when installing smart locks? What installation minefields need to be avoided? This article will take you to find out!
Pay attention to accurate positioning when opening holes.
When opening holes on the door surface, accurately locate the opening position according to the opening template.
If the positioning is not accurate, the panel will not be installed or installed offset, resulting in the phenomenon that the door can not be locked, or the lock tongue can not be retracted after successful verification.
(The picture shows the opening template of Philips smart lock)
When the lock body is fixed, it should be vertically centered.
The direction of the lock tongue should be consistent with the direction of opening the door. When fixing the lock body, it should be vertical and centered, and it should not be tilted up and down, left and right. When putting the lock body in, it should be easy and free, and it should not be forced, especially the cable should not be squeezed.
After the lock body is in place, it is fixed with screws. When fixing, the lock tongue cannot be punched out.
Pay attention to the thickness of the door panel when installing the outer panel.
When installing the outer panel, the connecting screw tube and square shaft with corresponding length should be selected according to the thickness of the door. The square shaft should be aligned with the square shaft hole, and the screw tube should be aligned with the hole position. If the square axis is too long, it will lead to the unsmooth opening and closing of the door.
Pay attention to the vertical outer panel when installing the fixing plate.
When fixing the outer panel with the fixing plate and screws on the inner side of the door, it should be noted that the outer panel must be vertical, so as not to affect the beauty and use of the smart lock.
When installing the inner panel, pay attention to plug the cable into place.
Insert the outer panel connecting wire and the lock body connecting wire into the corresponding sockets respectively, and pay attention to insert the cable in place, not backwards.
When inserting the square shaft into the lock body, arrange the cable, put the redundant cable into the vacant place, and don’t let the cable be squeezed. Then tighten the inner panel with fixing screws, plug the silicone plug, and install the battery and battery cover.
It is very important to confirm the position when installing the side gusset.
When installing the side gusset, adjust the clearance of the door to an appropriate position to make the door open and close smoothly. After the position of the side gusset plate is determined, fix the upper and lower ends with screws to prevent displacement in subsequent use.
Improper installation of the side gusset may block the main locking tongue, resulting in the following situations:
① After the door is closed, the main lock tongue can’t extend normally, giving an alarm sound and prompting that "the door is not locked".
(2) after closing the door, verify the lock, there will be an alarm.
When the above situation occurs, it is necessary to readjust the position of the side gusset plate. After confirming the position, screw the positioning holes at the upper and lower ends.
As an entry-level intelligent security artifact, smart lock has a zero tolerance attitude towards product quality and brand service, and the installation of smart lock determines its subsequent use experience and life span.
Don’t worry! Philips Smart Lock provides professional and free on-site installation services for all users.
If it is purchased on an online platform, such as Tmall or JD.COM, within 24 hours after receiving the goods (except in special circumstances), the staff will take the initiative to make an appointment for the installation time and confirm the relevant installation details, and then arrange the installation master to come to the door for service.
If it is an offline store purchase, you can communicate with the store staff on details such as installation time.
Did everyone get the details that need to be paid attention to when installing smart locks?
Even if a professional master comes to the door to install, we should carefully observe the installation process, and find out the problems in time, so as to better use the smart lock and play smart life.