Wrigley fingerprint lock supports multiple unlocking methods. Digital password and fingerprint identification run independently, which effectively reduces the failure rate. Wrigley fingerprint lock is a smart lock brand that many consumers love very much. So how to install the Wrigley fingerprint lock after buying it? What precautions are there when installing the Wrigley fingerprint lock? Let’s take a look.
How to install Wrigley fingerprint lock
First, determine the left and right direction of the door:
When we install, we need to determine the opening direction. Generally, most of them now open from the right. Here we also use this as an example. Of course, our friends can also choose other directions.
Second, the lock body installation:
1. Make sure that the direction of the locking tongue is consistent with the door opening direction. If it is not, jack up the inclined tongue with a screwdriver, rotate it for 180, and then loosen the screwdriver to reset it.
2. Then put the lock body into the opened door hole with the oblique tongue end as the upper end, let the lock body thread pass through the front of the door from the upper door hole, and then lock and fix the lock body with screws.
3. Put the lock core into the hole of the lock body from the outside of the door, and fix the lock core with the lock head screw. At this time, the lock body is partially installed. Use the mechanical key to test whether the lock tongue of the lock body works normally, and then install the panel.
Third, the panel installation:
1. Before installing the panel, install the handle according to the opening direction of the door. The front and rear panels should be parallel to the door, and the left and right distance should not be skewed to keep the handle consistent with the horizontal direction of the lock body. Adjust the vertical distance to keep the vertical direction of the handle and the lock body consistent.
2. First put the front lever into the lock body hole from the outside, then insert the lock body wire into the panel bus, and the male wire passes through the door hole to the back of the door. At this time, put the square lever spring into the handle hole, align the handle square hole of the front panel with the front lever, and then install the rear bottom plate from the inside of the door and fix the rear bottom plate and the front panel on the door with screws.
3. Then put the rear lever into the square hole of the lock body from the inside of the door, put the spring into the handle hole of the rear panel, and insert the connecting wire of the rear panel and the public wire of the front panel.
4. Plug the excess wire into the door hole, then put the front panel into the rear pole and install it on the door, and lock it with screws.
5. Then install four No.5 alkaline batteries to test the installation and function of the lock.
Four, buckle box buckle plate installation:
1. After the fingerprint lock is tested normally, the buckle box and gusset plate can be installed on the door frame. Pay attention to the direction of the upper and lower ends of the gusset plate, and the square hole is at the upper end.
2. Then open and close the door to see if the closure of the buckle box and the latch door frame is normal. Note that it is best to have people inside and outside the door at this time, in case the door cannot be opened during the test. So our door lock is installed.
Matters needing attention in installation of Wrigley fingerprint lock
1) Because the door is not opened in the same way, the hole position on the installation mold is also different, so the correct position must be determined before installation.
2) Lock the front and rear leads, sockets and plugs to ensure correct connection.
3) Before installation, the installation height should be determined, and then the installation mould should be pasted at the corresponding position, and the position to be drilled should be drawn with a pencil.
4) When drawing holes, the folding edge of the installation mold must be perpendicular to the door frame, otherwise it will cause the lock body not to be perpendicular to the door after installation.
5) The lock core is generally required to be installed in the middle of the door thickness.
6) After opening the hole in the door frame, be sure to clean up the sawdust or other foreign objects in the hole to prevent the door from falling into the lock body when the switch vibrates.
The above is about how to install Wrigley fingerprint lock and what matters needing attention. Keep these contents in mind, and you can install them yourself when you buy and install Wrigley fingerprint lock in the future.